Honda ADAS Calibration Operation Instructions

Advanced Driver Assistance Systems (ADAS) have become a vital component of modern vehicles, enhancing safety, reducing human error, and aiding drivers in critical moments. The Honda is equipped with a sophisticated ADAS suite, including features such as lane departure warning, forward collision warning, and adaptive cruise control. Proper calibration of ADAS sensors especially after repairs, replacements, or error codes is crucial to ensure their accurate functionality.

This comprehensive guide details the ADAS calibration procedure for the Honda , helping technicians, workshop professionals, and Honda vehicle owners understand the process, requirements, and best practices for both static and dynamic camera calibration.

Why ADAS Calibration is Crucial

Importance of Calibration After Repairs

Incorrect calibration can lead to:

• Unreliable adaptive cruise control
• Reduced road safety
• Inaccurate lane detection
• Faulty collision warnings

Calibration is typically required after:

• Suspension or wheel alignment changes
• Error codes related to ADAS functions
• Replacing the front camera
• Replacing the windshield

Common Calibration Fault Codes in Honda

If you encounter the following Diagnostic Trouble Codes (DTCs), calibration is necessary:

• B2A60-54 – Static camera alignment not done
• B2A60-52 – Dynamic camera alignment not done

These codes often appear after camera replacement, windshield installation, or ADAS control module resets.

Pre-Calibration Checklist

Before starting the calibration process, ensure the following:

• The vehicle is parked on a level surface.
• The calibration area is free of obstacles.
• All unrelated fault codes are cleared.
• The camera lens is clean and unobstructed.
• There are no direct light sources interfering with the camera.

Equipment Required

To perform a successful calibration, you’ll need:

• ADAS Calibration Tool (ADAS Mobile or equivalent)
• LAM01-20 targets (for lateral calibration)
• Measuring tools (to set distances and height)
• Diagnostic scan tool compatible with Honda models

✅ Pro Tip: Use OE-approved tools to ensure accuracy and compliance with manufacturer standards.

Step-by-Step Guide to Honda ADAS Calibration

1. Scan the VIN

• • Use a scan tool to read the Vehicle Identification Number (VIN)
  • Select the appropriate model and region (e.g., USA)

2. Access ADAS Calibration Module

• • Navigate to the ADAS Calibration section in the diagnostic software.
  • Select “Front Camera Calibration”
  • Choose the device type select ADAS Mobile if using that platform.

3. Static Camera Calibration

a) Target Placement

• • Set up the target at a distance of 6000mm in front of the vehicle.
  • Adjust the height to 1150mm.
  • Ensure the target is perfectly parallel to the vehicle’s centerline.
  • Mark reference points A and B to ensure alignment.

b) Hub Height Measurement

• • Measure the height of both front wheel hubs.
  • Compare with standard values to calculate the error range.
  • Choose the error range setting in the calibration tool (e.g., -15mm to -5mm).

c) Intermediate Target Calibration

• • Calibrate the center target first.

d) Side Target Calibration

• • Install LAM01-20 800mm to the left of the centerline. Calibrate.
  • Then move the target 800mm to the right. Calibrate.

e) Complete Static Calibration

• • Once completed, turn off and restart the ignition.
  • Review the ADAS calibration report to confirm success.

Dynamic Camera Calibration (If Required)

Dynamic calibration is prompted automatically if required.

Conditions:

• Drive the vehicle at a consistent speed of 72–110 km/h (45–70 mph)
• Stay centered in the lane
• Avoid sudden lane changes or erratic driving

Steps:

1. Select “Dynamic Camera Aiming” in the ADAS tool.
2. Follow on-screen prompts.
3. Drive as specified until the tool confirms calibration is complete.
4. Park the vehicle, turn off and restart the ignition.
5. Review the final ADAS calibration report.

Post-Calibration Checklist

• Confirm that all DTCs have cleared.
• Test-drive the vehicle to verify proper ADAS functionality.
• Print and store the calibration report for service records.

When Should You Recalibrate the Honda ADAS?

Use this quick reference checklist:

Condition

Calibration Needed

Windshield replacement

✅ Yes

Front camera removal or replacement

✅ Yes

Suspension repair or adjustment

✅ Yes

Front-end collision repair

✅ Yes

Fault codes B2A60-54 or B2A60-52

✅ Yes

Software or module update

✅ Yes

Regular service without component change

❌ No

Common Issues During Calibration (and Fixes)

Issue

Cause

Solution

Calibration fails

Target not aligned correctly

Re-check distances and alignment

Error code persists

Fault not cleared before calibration

Clear all unrelated DTCs

Dynamic calibration not completing

Driving too slow or erratic

Maintain required speed and lane position

ADAS tool not detecting vehicle

Wrong region or VIN mismatch

Confirm correct vehicle selection

Conclusion

Proper calibration of the Honda ADAS system is essential for ensuring driver safety and system reliability. Whether you’re a certified technician or an advanced DIYer, following the correct steps using the appropriate tools guarantees that the front camera system functions accurately and complies with Honda’s OEM standards.

Always remember to:

• Use OE-approved calibration tools
• Follow structured calibration sequences
• Keep detailed service logs and calibration reports

Failing to calibrate after repairs or part replacements can lead to serious safety implications and potential liability. Stay compliant, stay safe.

Frequently Asked Questions (FAQs)

Q1: Can I skip static calibration if the camera is only slightly misaligned?

A: No. Even minor deviations can cause serious ADAS inaccuracies. Always perform full calibration.

Q2: Does calibration require a professional shop?

A: While DIY is possible with the right tools and knowledge, professional calibration is recommended for accuracy and liability coverage.

Q3: How long does the entire calibration take?

A: Static calibration typically takes 30–45 minutes; dynamic calibration may require 10–20 minutes of highway driving.

Q4: What happens if I don’t recalibrate after replacing the windshield?

A: The ADAS system may not function properly, increasing the risk of incorrect safety alerts or system failure.

**Need help with your Honda ADAS calibration?**Contact a certified technician or visit us for a diagnosis